Citation: | WANG Zhiming, FANG Xiaohong, SUN Wucheng, DUAN Longchen, TAN Songcheng, ZHANG Wenjiao. Effect of sintering pressure on the performance of Fe-based pre-alloyed bit matrix with low liquid phase[J]. Diamond & Abrasives Engineering, 2023, 43(2): 151-160. doi: 10.13394/j.cnki.jgszz.2022.3007 |
The hot-pressing sintering experiments were carried out under the conditions of sintering temperature of 950 ℃, holding time of 5 mins and different sintering pressures. The effects of sintering pressure on the properties of three kinds of low liquid phase Fe-based pre-alloyed bit matrix and one traditional Fe-based bit matrix were compared and studied, including the hardness, the bending strength, the relative density, the diamond embedding strength of the matrix, the thermal damage of diamond. as well as the microstructure and the morphology of drill bit matrix. The results show that with the increase of sintering pressure, the indentation hardness, the bending strength and the relative density of blank matrix with low liquid phase gradually increase, but the hardness and the bending strength of traditional Fe-based pre-alloyed blank matrix increase at first and then decrease, and the relative density increases. For the matrix containing diamonds, the bending strength of low liquid phase and traditional Fe-based matrix increases with the increase of sintering pressure. When the sintering pressure is 20 MPa, the bending strength of the diamond containing matrix with low liquid phase tends to be stable, while the bending strength of the traditional Fe-based matrix containing diamond decreases slightly. At the same time, with the increase of sintering pressure, the homogeneity of the low liquid phase matrix is enhanced, but the thermal damage of the diamond is gradually aggravated. According to the analysis of the mechanical properties and the fracture morphology of the matrix, the optimal sintering pressure is 20MPa. At this time, the hardness and the bending strength of the low liquid phase Fe-based pre-alloy matrix can meet the requirements of impregnated diamond bits.
[1] |
吕智, 刘志环, 潘晓毅, 等. 深部找矿金刚石钻进工具发展现状和趋势 [J]. 超硬材料工程,2013,25(4):39-44. doi: 10.3969/j.issn.1673-1433.2013.04.010
LYU Zhi, LIU Zhihuan, PAN Xiaoyi, et al. Development status and trends of deep prospecting diamond tools [J]. Superhard Material Engineering,2013,25(4):39-44. doi: 10.3969/j.issn.1673-1433.2013.04.010
|
[2] |
TAN S C, LI C P, FANG X H, et al. Investigation of filling phase percentages on the performance of WC-Cu based hot-pressing diamond bit matrices [J]. Metals,2019,9(12):1305. doi: 10.3390/met9121305
|
[3] |
LI W S, ZHANG J, WANG S C, et al. Characterizations and mechanical properties of impregnated diamond segment using Cu-Fe-Co metal matrix [J]. Rare Metals,2012,31(1):81-87. doi: 10.1007/s12598-012-0467-x
|
[4] |
侯明, 郭胜惠, 高冀芸, 等. 预合金结合剂成分及烧结工艺对金刚石工具性能的影响 [J]. 材料导报,2019,33(14):2403-2407. doi: 10.11896/cldb.18050079
HOU Ming, GUO Shenghui, GAO Jiyun, et al. Effect of pre-alloyed powder with different composition and sintering process on performance of diamond tools [J]. Materials Reports,2019,33(14):2403-2407. doi: 10.11896/cldb.18050079
|
[5] |
XIE D L, WAN L, SONG D D, et al. Low temperature sintering of FeCoCu based pre-alloyed powder for diamond bits [J]. Journal of Wuhan University of Technology-Material Science Edition,2016,31(5):805-812.
|
[6] |
董书山, 刘晓旭, 李长青, 等. 超硬材料工具用金属预合金粉末的国内发展现状及趋势 [J]. 超硬材料工程,2012,24(1):43-47. doi: 10.3969/j.issn.1673-1433.2012.01.011
DONG Shushan, LIU Xiaoxu, LI Changqing, et al. Analysis on domestic situation and development trend of pre-alloyed metal powder for diamond tools in China [J]. Superhard Material Engineering,2012,24(1):43-47. doi: 10.3969/j.issn.1673-1433.2012.01.011
|
[7] |
JIA M L, CAI J P, OUYANG Z Y, et al. Design & application of diamond bit to drilling hard rock in deep borehole [J]. Procedia Engineering,2014,73:134-142. doi: 10.1016/j.proeng.2014.06.181
|
[8] |
高雅, 钟素娟, 纠永涛, 等. 金刚石工具用预合金粉末的制备及应用研究进展 [J]. 粉末冶金工业,2016,28(2):65-71. doi: 10.13228/j.boyuan.issn1006-6543.20170137
GAO Ya, ZHONG Sujuan, JIU Yongtao, et al. Research progress on preparation and application of pre-alloyed powder for diamond tools [J]. Powder Metallurgy Industry,2016,28(2):65-71. doi: 10.13228/j.boyuan.issn1006-6543.20170137
|
[9] |
SUN Y X, TSAI Y T, LIN K K. The influence of sintering parameters on the mechanical properties of vitrified bond diamond tools [J]. Materials & Design, 2015, 80 (95): 89.
|
[10] |
孙为云, 康杰, 丁紫阳, 等. 预合金粉含量对铁基胎体微观组织及性能的影响 [J]. 金刚石与磨料磨具工程,2020,40(3):62-66. doi: 10.13394/j.cnki.jgszz.2020.3.0010
SUN Weiyun, KANG Jie, DING Ziyang, et al. Influence of pre-alloyed powder content on microstructure and properties of iron-based matrix [J]. Diamond & Abrasives Engineering,2020,40(3):62-66. doi: 10.13394/j.cnki.jgszz.2020.3.0010
|
[11] |
刘震鹏, 闫志巧, 陈峰, 等. 金刚石工具用Cu-10Sn-x Ni合金的制备和性能表征 [J]. 金属学报,2020,56(5):760-768.
LIU Zhenpeng, YAN Zhiqiao, CHEN Feng, et al. Fabrication and performance characterization of Cu-10Sn-x Ni alloy for diamond tools [J]. Acta Metallurgica Sinica,2020,56(5):760-768.
|
[12] |
刘志环, 张绍和. Co质量分数对FeCuCo预合金粉烧结与力学性能的影响 [J]. 中南大学学报(自然科学版),2019,50(12):2958-2968.
LIU Zhihuan, ZHNG Shaohe. Effect of Co content on sintering and mechanical properties of FeCuCo pre-alloyed powder [J]. Journal of Central South University (Science and Technology),2019,50(12):2958-2968.
|
[13] |
金鑫. 新型热压WC-Fe基金刚石钻头钻进试验 [J]. 煤田地质与勘探,2014,42(6):117-120. doi: 10.3969/j.issn.1001-1986.2014.06.025
JIN Xin. Drilling test of new type of hot pressed tungsten carbide and iron-based diamond bit [J]. Coal Geology & Exploration,2014,42(6):117-120. doi: 10.3969/j.issn.1001-1986.2014.06.025
|
[14] |
莫松林, 周天盛, 唐兰艳, 等. 铁铜类预合金粉末应用于热压金刚石钻头的试验研究 [J]. 超硬材料工程,2017,29(3):28-30. doi: 10.3969/j.issn.1673-1433.2017.03.005
MO Songlin, ZHOU Tiansheng, TANG Lanyan, et al. Experimental study of the application of iron copper pre-alloyed powder in hot pressing diamond bit [J]. Superhard Material Engineering,2017,29(3):28-30. doi: 10.3969/j.issn.1673-1433.2017.03.005
|
[15] |
杨洋, 潘秉锁, 杨凯华. 热压铁基金刚石钻头胎体性能及钻进试验研究 [J]. 金刚石与磨料磨具工程,2009(2):41-43, 61. doi: 10.3969/j.issn.1006-852X.2009.02.010
YANG Yang, PAN Bingsuo, YANG Kaihua. Study on matrix performance of iron-based diamond bit and and drilling tests [J]. Diamond & Abrasives Engineering,2009(2):41-43, 61. doi: 10.3969/j.issn.1006-852X.2009.02.010
|
[16] |
谢志刚, 秦海青, 刘心宇, 等. 金刚石制品用FeCoCu预合金粉末的制备及应用研究 [J]. 材料工程,2011(3):1-5,64. doi: 10.3969/j.issn.1001-4381.2011.03.001
XIE Zhigang, QIN Haiqing, LIU Xinyu, et al. Study on the preparation of the pre-alloyed powder and its application for diamond tools [J]. Journal of Materials Engineering,2011(3):1-5,64. doi: 10.3969/j.issn.1001-4381.2011.03.001
|
[17] |
LI C L, DUAN L C, TAN S C, et al. Effect of CaF2 and hBN on the mechanical and tribological properties of Fe-based impregnated diamond bit matrix [J]. International Journal of Refractory Metals & Hard Materials,2018,75:118-125. doi: 10.1016/j.ijrmhm.2018.04.011
|
[18] |
董虎林, 包海萍, 彭建洪. TiC含量对铁基复合材料力学性能及耐磨性能的影响 [J]. 金属学报,2019,55(8):1049-1057. doi: 10.11900/0412.1961.2018.00373
DONG Hulin, BAO Haiping, PENG Jianhong. Effects of TiC content on mechanical properties and wear resistance of Fe-matrix composites [J]. Acta Metallurgica Sinica,2019,55(8):1049-1057. doi: 10.11900/0412.1961.2018.00373
|
[19] |
沈立娜, 阮海龙, 吴海霞, 等. 稀土La添加量对预合金铁基胎体性能的影响 [J]. 探矿工程(岩土钻掘工程),2012,39(4):69-71.
SHEN Lina, RUAN Hailong, WU Haixia, et al. Influence of La addition on the properties of pre-alloyed Fe-based matrix material [J]. Exploration Engineering (Rock & Soil Drilling and Tunneling),2012,39(4):69-71.
|
[20] |
周强, 杨树忠, 常德民, 等. W对热压烧结铁基金刚石工具胎体组织性能的影响 [J]. 中国钨业,2008,33(3):61-66.
ZHOU Qiang, YANG Shuzhong, CHANG Demin, et al. Effect of W on the microstructure and properties of hot pressed sintered iron matrix diamond tools [J]. China Tungsten Industry,2008,33(3):61-66.
|
[21] |
WANG L, GUO S H, GAO J Y, et al. Microwave sintering behavior of FeCuCo based metallic powder for diamond alloy tool bit [J]. Journal of Alloys and Compounds,2017,727:94-99. doi: 10.1016/j.jallcom.2017.08.132
|
[22] |
ZHAO X J, LI J Y, DUAN L C, et al. Effect of Fe-based pre-alloyed powder on the microstructure and holding strength of impregnated diamond bit matrix [J]. International Journal of Refractory Metals & Hard Materials,2019,79:115-122. doi: 10.1016/j.ijrmhm.2018.11.015
|
[23] |
ZHAO X J, DUAN L C. A review of the diamond retention capacity of metal bond matrices [J]. Metals, 2018, 8(5): 307.
|
[24] |
余桂红, 焦星东, 李静仪, 等. 配方预合金化对提高热压富铁基含金刚石钻头胎体性能的影响机理 [J]. 地质科技情报,2008,37(5):260-268. doi: 10.19509/j.cnki.dzkq.2018.0536
YU Guihong, JIAO Xingdong, LI Jingyi, et al. Effect mechanism of formula pre-alloying on improving hot-pressured bit iron-rich matrix performance [J]. Geological Science and Technology Information,2008,37(5):260-268. doi: 10.19509/j.cnki.dzkq.2018.0536
|
[25] |
杜全斌, 龙伟民, 路全彬, 等. Cu85Sn15粘结剂对铁基胎体抗弯性能的影响 [J]. 焊接学报, 2017, 38(3): 45 -48, 131.
DU Quanbin, LONG Weimin, LU Quanbin, et al. Effect of Cu85Sn15 binder on bending performance of iron based-matrix [J]. Transactions of the China Welding Institution, 2017, 38(3): 45-48, 131.
|
[26] |
孙吉伟, 吴海霞, 沈立娜, 等. 不锈钢纤维网对热压铁基预合金胎体抗冲击韧性的影响 [J]. 探矿工程(岩土钻掘工程),2020,47(2):73-77.
SUN Jiwei, WU Haixia, SHEN Lina, et al. Effect of stainless steel fiber mesh on impact toughness of hot-pressed iron-based pre-alloyed carcass [J]. Exploration Engineering (Rock & Soil Drilling and Tunneling),2020,47(2):73-77.
|
[27] |
许华松, 杨俊德, 陈威. 保温时间对Fe基金刚石钻头性能影响的研究 [J]. 超硬材料工程,2016,28(4):1-5. doi: 10.3969/j.issn.1673-1433.2016.04.001
XU Huasong, YANG Junde, CHEN Wei. Study of the influence of holding time on the performance of iron based diamond drill bit [J]. Superhard Material Engineering,2016,28(4):1-5. doi: 10.3969/j.issn.1673-1433.2016.04.001
|
[28] |
肖长江, 赵延军, 尚秋元. 烧结工艺对铁基结合剂金刚石节块力学性能的影响 [J]. 硅酸盐通报,2011,30(5):1068-1071. doi: 10.16552/j.cnki.issn1001-1625.2011.05.027
XIAO Changjiang, ZHAO Yanjun, SHANG Qiuyuan. Effect of sintering process on properties of Fe-matrix bonding diamond tool bits [J]. Bulletin of the Chinese Ceramic Society,2011,30(5):1068-1071. doi: 10.16552/j.cnki.issn1001-1625.2011.05.027
|
[29] |
刘伟, 潘飞飞, 杨晖, 等, 磁处理参数对热压铁基金刚石钻头胎体力学性能影响 [J]. 地质科技情报, 2018, 37(5): 269-274.
LIU Wei, PAN Feifei, YANG Hui, et al. Effects of magnetic treatment parameters on the physical performance of the first tire of hot-pressed iron diamond [J]. Geological Science and Technology Information, 2018, 37 (5): 269-274.
|
[30] |
高雅. Ni、Sn对Fe基金刚石工具胎体组织及性能影响 [D]. 北京: 机械科学研究总院, 2018.
GAO Ya. Influence of nickel and tin on the microstructure and performance of Fe-based matrixes for diamond tools [D]. Beijing: China Academy of Machinery Science and Technology, 2018.
|
[31] |
MECHNIK V A, BONDARENKO N A, KUZIN N O, et al. The role of the structure formation in forming the physicomechanical properties of composites of the diamond–(Fe–Cu–Ni–Sn) system [J]. Journal of Friction and Wear,2016,37(4):377-384. doi: 10.3103/S1068366616040139
|
[32] |
李颖颖, 万隆, 王俊沙, 等. 温度对铁基预合金粉腐蚀泡沫化人造金刚石微粉的影响 [J]. 材料导报,2017,31(14):113-116, 142. doi: 10.11896/j.issn.1005-023X.2017.014.024
LI Yingying, WAN Long, WANG Junsha, et al. Influence of temperature on etching and foaming behavior of synthetic diamond powder by iron-based pre-alloyed powders [J]. Materials Reports,2017,31(14):113-116, 142. doi: 10.11896/j.issn.1005-023X.2017.014.024
|